Tuesday, August 6, 2019
Potassium Lithium Hydrogen Phthalate Mixed Crystals
Potassium Lithium Hydrogen Phthalate Mixed Crystals 3. RESULTS AND DISCUSSION SECTION 3.1 Synthesis, growth, structure and characterization of potassium lithium hydrogen phthalate mixed crystals* In the present work, we report the growth and structure of a new mixed crystal C16H16KLiO11 (PLHP), which crystallizes in a non-centrosymmetric space group P21 and SHG-active. The grown crystals were subjected to various characterization studies which are briefly described below. Here it is established that by synthesising the mixed crystal in a different route with a controlled concentration of additive, one can sustain nonlinearity at the macro level by allowing the specimen to crystallise in a polar space group. The main objective of the investigation is to design a noncentrosymmetric structure by attempting a different route of synthesis, leading to NLO activity. Steering to noncentrosymmetry from centrosymmetry is made possible by changing the growth conditions. 3.1.1. Crystal growth The mixed crystal PLHP was synthesized from an aqueous solution containing equimolar quantities of AR grade potassium hydrogen phthalate (KHP) and lithium carbonate (Li2CO3) in slightly acidic conditions using de-ionized water. After successive recrystallization, the mixed crystals were grown by the slow evaporation solution growth technique. The crystallization took place within 20-25 d and the crystals were harvested. Photographs of as- grown crystals are shown in Fig. 3.1.1. Fig. 3.1.1. Photographs of mixed crystal PLHP 3.1.2. FT-IR The FT-IR spectrum of the as-grown specimen is shown in Fig.3.1.2. An absorption band in the region 500-900 cm-1 corresponds to the C-H out of plane deformations of aromatic ring. The C=O stretching frequency appeared at 1670 cm-1. The characteristic vibrational patterns of KHP104, lithium hydrogen phthalate (LiHP) 22 and PLHP are given in Table 3.1.2. A slight shift of some of the characteristic vibrational frequencies could be due to the stress development because of Li incorporation. Fig. 3.1.2. FT–IR spectrum of mixed crystal PLHP Table 3.1.2. FT-IR frequencies of some acid phthalate crystals (cm-1) aRef 105 bRef 22 c Present study 3.1.3. TGA/DTA Thermal studies reveal the purity of the material. The TGA curve shows a single stage weight loss at à ¯Ã‚  ¾150o C due to loss of water molecule. In DTA, the broad endothermic peak at 420 °C, is due to decomposition. The residual mass observed from thermogram at 600 °C is ~50%. (Fig. 3.1.3). 3.1.4. SEM / EDS The SEM micrographs give information about the surface morphology and it is used to check the imperfections105. The SEM pictures of PLHP at different magnifications are shown in Fig. 3.1.4.1. It shows highest surface roughness in a plate like structure, due to defect centers and crystal voids. The presence of Li and K in the PLHP crystal lattice is confirmed by energy dispersive spectroscopy (EDS) (Fig. 3.1.4.2). Fig. 3.1.4.2. EDS spectrum of PLHP 3.1.5. AAS and CHN analysis Atomic absorption spectroscopic studies were carried out to quantify Li (20.6 ppm) and K (21. ppm ) in the sample. Also, CHN elemental analysis was performed to estimate the quantity of carbon and hydrogen present in PLHP. The elemental composition found was: C 42.93%, H 3.29%. The calculated composition was: C 44.63%, H 3.7%. 3.1.6. UV-visible The UV-visible spectrum of the mixed crystal PLHP reveals high transmittance in the visible region and the lower cut-off wave length is observed at ~300 nm. Incorporation of foreign metal ion into the KHP crystal lattice does not destroy the optical transmission of potassium hydrogen phthalate. The concentration of an absorbing species can be determined using the Kubelka-Munk equation106 correlating reflectance and concentration, F(R) = (1-R)2 / 2R = ÃŽ ± / s=Ac / s where F(R) is Kubelka-Munk function, R is the reflectance of the crystal, ÃŽ ± is absorption coefficient, s is scattering coefficient, A is absorbance and c is concentration of the absorbing species. The direct band-gap energy of the specimen is estimated as 4.05 eV, from the Tauc plot [F(R)hÃŽ ½]2 versus hÃŽ ½ (eV) (Fig. 3.1.6). Fig. 3.1.6. Tauc plot (Direct Band gap energy) 3.1.7 X-ray diffraction analysis The powder XRD pattern of PLHP shows that the sample is of a single phase without a detectable impurity. Narrow peaks indicate the good crystallinity of the material. At room temperature all the observed reflections were indexed. The indexed powder XRD pattern is shown in Fig. 3.1.7.1. Peak positions in powder XRD match with simulated XRD patterns from single crystal X-ray diffraction. The relative intensity variations could be due to the preferred orientation of the sample used for diffractogram measurement. Also, the mosaic spread of powder and single crystal patterns may differ, resulting in intensity variations. The structure of PLHP is elucidated and the ORTEP is given as Fig. 3.1.7.2. Three-dimensional view of intramolecular hydrogen bonding interactions is displayed in Fig. 3.1.7.3. The chemical formula C16H16KLiO11 confirms the presence of K and Li in the crystalline matrix, well supported by energy dispersive X-ray spectroscopy (EDS) and atomic absorption spectroscopy (AAS). The specimen crystallizes in the monoclinic crystal system with the noncentrosymmetric space group P21. The crystallographic parameters of PLHP, KHP, LiKP and LiHP are listed in Table 3.1.7.1. Fig.3.1.7.1. Experimental (red) and simulated (blue) powder XRD patterns Fig.3.1.7.2. ORTEP of PLHP Fig.3.1.7.3. Three dimensional view of intramolecular hydrogen bonding interactions (OHà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O) Table 3.1.7.1. Crystal data of LiHP, KHP, LiKP and PLHP crystals The alkali ions are linked to each other by O–Hà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O hydrogen bonds through the carboxylate oxygen. The O atoms of the carboxylate group (in phthalate ions) namely O(1)-O(8) are connected to K1, while the lithium ions are connected with central metal ion via O(5)-O(6), O atoms of the water molecules. The K-O bond distances range from 2.8311 (19) to 3.207 (8) Ã…, which is higher than bond distances observed in potassium hydrogen phthalate monohydrate 2.305 (1) –2.597 (1) Ã…. The Li–O bond distances lie in the range 1.956 (3)–1.968 (3) Ã…. The aromatic C-C bond distances fall in the range 1.377 (3) –1.485 (2) Ã…. The four carboxy C-O distances are almost same and the values are close to that observed for potassium hydrogen phthalate monohydrate107 and sodium acid phthalate108. In LiKP, O(4)–K(1) bond distance lies at 2.7491 Ã… whereas in our present study, the O(4)–K(1) bond dist ance is 2.7671 Ã…. The selected bond angles and bond lengths are given in Table 3.1.7.2. Crystal packing with hydrogen bonding interactions along the b-axis is given in Fig. 3.1.7.4. Strong intramolecular hydrogen bonding interactions are O(2)-H(2)à ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O(11) and O(5)-H(5B)à ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O(3) assembled with distances of 1.77 and 1.86 Ã… respectively (Fig. 3.1.7.5). Weak intermolecular interactions are observed for O(7)-H(7B)à ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O(10), O(7)-H(7B)à ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O(11) and O(5)-H(5B)à ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O(1), with bond distances of 2.41 (2), 2.46 (3) and 3.25 (4) Ã… respectively (Table 3.1.7.3.). Table 3.1.7.2. Selected bond lengths (Ã…) and angles (o) of PLHP Table 3.1.7.3. Hydrogen bonds geometry for PLHP [Ã…, o] Fig. 3.1.7.5. Three dimensional image of polyhedron with O-Hà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O interactions 3.1.8. SHG efficiency In order to confirm the influence of incorporation of lithium on the NLO properties of KHP the pure and mixed crystals were subjected to SHG test with an input radiation of 6.5 mJ/pulse. The outputs give the relative SHG efficiencies of the measured specimens. As seen, the SHG activity of the mixed crystal is comparable with that of KHP (Fig. 3.1.8) and it is quite likely due to the facile charge transfer, not disturbed by Li-incorporation. Although many materials have been identified that have higher molecular nonlinearities, the attainment of second-order effects requires favourable alignment of the molecule within the crystal109. It has been reported that the SHG can be greatly enhanced by altering the molecular alignment through inclusion complexation110. The mixed crystal PLHP grown from an aqueous solution containing equimolar quantities of reactants crystallize in a noncentrosymmetric space group P21 and SHG-active, whereas when Li is taken in excess in the growth medium the f ormed mixed crystal LiKP crystallizes in a centrosymmetric space group P1 and hence SHG-inactive29. It is interesting to observe that the mixed crystal of KHP synthesized by a different route crystallises in a polar space group. By changing the growth conditions it is possible to attain noncentrosymmetry in preference to centrosymmetry, a required characteristic of an NLO material. Fig. 3.1.8. The comparative SHG oscilloscope traces of the powder samples of KHP (red) and PLHP (blue) 3.1.9. Hirshfeld surface analysis The Hirshfeld surfaces of PLHP have been demonstrated in Fig. 3.1.9.1 by showing dnorm, shape index, de and di. The Hirshfeld surface111-113 surrounding a molecule is defined by points where the contribution to the electron density from the molecule under consideration is equal to the contribution from all the other molecules. For each point on that isosurface, two distances are determined: one is de representing the distance from the point to the nearest nucleus external to the surface and second one is di, representing the distance to the nearest nucleus internal to the surface. The normalized contact distance (dnorm) is based on both de and di. The surfaces are shown as transparent to allow visualization of the molecule around which they were calculated. The circular depressions (deep red) which are visible on the Hirshfeld surface are an indicator of hydrogen bonding contacts and other visible spots in Fig. 3.1.9.1a are due to Oà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Li ( 3.6%), Hà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O (14.5%), Oà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢H (15.9%), Kà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O (2.0%) and Lià ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O (3.5%) interactions. The short interactions represented by deep red spots in de surface (Fig.3.1.9.1c) are Oà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Li contacts (3.6%). The dominant Oà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢H (14.5%), Lià ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O (3.5%) and Hà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢H (31.7%) interactions are viewed in di surface plots by the bright red area in Fig. 3.1.9.1d. The shape index indicates the shape of the electron density surface around the molecular interactions. The small range of area and light color on the surface represent a weaker and longer contact other than hydrogen bonds. The two-dimensional fingerprint plots114 of PLHP exemplify the strong evidenc e for the intermolecular interactions pattern. In the fingerprint region (Fig. 3.1.9.3), Oà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢H (15.9%) interactions are represented by a spike in the bottom area whereas the Hà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O (14.5%) interactions are represented by a spike in the top left region. Hydrogen-hydrogen interactions Hà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢H (31.7%) are very high while compared to the other bonding interactions. Sharp curved spike at the bottom left area indicates the Oà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Li (3.6%) and top left corner with curved spike indicates the Lià ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢O (3.5%). The finger print at the bottom right area represents Cà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢H (11.7%) interactions and top right area represents Hà ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢Ãƒ ¢Ã‹â€ â„ ¢C (8.7%) interactions. The number of interactions in terms of percent age are represented in a pie chart in Fig. 3.1.9.2. Fig.3.1.9.1. Hirshfeld surface analysis of PLHP (a) dnorm (b) shape index (c) de (d) di Fig. 3.1.9.2. Relative contribution of various intermolecular interactions in PLHP Fig. 3.1.9.3. Fingerprint plots of PLHP 1
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment
Note: Only a member of this blog may post a comment.